Peugeot 3008 Key Fob Problems
Peugeot's mid-sized 3008 SUV has lot of positives. It is well-constructed, drives great and has a big boot. But can it beat against strong competition in the most crowded area of the market?
If your Peugeot keyfob does not work it is possible that it was exposed to clean or soapy tap water. You may have to remove the battery and clean it with electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs come with small coin batteries that powers their remote locking as well as other functions. This battery has a limited lifespan and can get worn out after years of usage. The test of voltage is a quick method to determine if the battery is defective. A multimeter is used to determine the voltage between the battery's plus and the minus poles. The results of this test will show whether the battery is dead or not.
The receiver module could be the reason for your key fobs not working after using your Peugeot 3008 a long time. The receiver module is in charge of receiving radio frequency signals sent by the key fobs, and sending them out to car systems. If the receiver module is defective or damaged, it will not be able send commands to other modules of the vehicle.
Another reason for the key fob not working is moisture or sweat in the circuit board. This can lead to short circuits that drain the battery and disable the remote locking feature of the key fob. If this is the case, you should take your key fob to an expert in chip level repair to repair it.
Water damage
Whether you dropped your key fob into the pool, threw it in the washing machine or even left it in the rain for too long, water damage can be a real problem. Water makes for a good conductor and can easily cut off parts of the circuit board. It could also cause corrosion of the traces of metal and other components of the key fob. A wet circuit can also cause the battery to lose its charge.
If you have an additional key fob, use it to lock/unlock the Peugeot 3008 in order to eliminate a dead coin-cell battery as the reason for the problem. Another issue that can stop the key fob from operating properly is interference signals that interfere with the signal that is sent to the receiver module. These interference signals can come from a variety of things including radio transmitters that are near.
If you hear sloshing noises emanating from the interior of your Peugeot 3008 during your drive, it's probably due to a blocked evaporator condensate drain. You can test this by blowing compressed air through the drain holes beneath your door. You can also use a flexible metal wire to move drain holes around to clean any dirt that has built up. Air pockets can also be detected by sloshing noises.
The receiver module is not working properly.
The receiver module on a Peugeot 3008 key fob is responsible for sending the remote keyless system signal from the key fob to the car's receiver. The receiver module may be damaged and stop the car from acknowledging your key fob. Other causes of this issue include a dead battery water damage or interference from electronic devices that operate on the same frequency as the key fob. In G28 might display a message saying "card not detected" on the display.
There are many options to resolve this problem. You might try replacing the battery, or reprogramming the key fob. You can also start your vehicle with a spare key. However, if the key fob isn't working after all these steps, it could have a chip that's not working properly.
The best way to determine whether the key fob is equipped with damaged chip is to take it off and clean it with a paper towel and rub alcohol. If the chip is fried you must purchase an entirely new one. FB Series enclosures are designed for a key fob and come with an additional coin cell battery holder that fits the most common type of key fob batteries. They can also be personalized by using digital printing or CNC machined cutouts. If your key fob has been exposed to dirty or salty tap water, the chip might be contaminated and must be cleaned.
Faulty keyless entry systems
If you see the message "card not detected" It signifies that your car can't receive an alert from your key fob. This can be due to a variety of causes including the battery being weak or dead. In most cases, the issue will be resolved by pushing the start button with the key fob. In some cases, however, you may require taking the key fob to an Peugeot dealership for additional repairs.
The first step to fix the problem with a Peugeot 3008 key fob that won't unlock or lock the doors is to check the battery. Batteries are usually the cause of an issue with the key fob. However there are other factors that may be at play. This includes worn buttons and water damage.
If your Peugeot key fob has been exposed to clean tapwater, it's a good idea to remove the battery. Then, dry the electronic components with paper towel. You can also utilize a cleaner or Isopropyl ethanol to do this. It's best to change the fob if it's been exposed to salt water or soapy water.
If your key fob is not working, you can try to reset it by disconnection of the battery at 12 volts for approximately 15 minutes. Then reconnect the negative cable first, followed by the positive cable.